Attic Access Insulation and Air Sealing

Adequately insulating and air sealing the access to an attic— especially to unconditioned attics—will help lower your heating and cooling bills.

A home’s attic access, which could be an attic hatch, pull-down stairs, or a knee-wall door, often goes uninsulated. This gap in the attic insulation increases heat loss in the winter and heat gain in the summer.

These accesses also often aren’t sealed properly. A 1/4-inch gap around the perimeter of an attic access can potentially leak the same amount of air supplied by a typical bedroom heating duct.

Before insulating your attic access, you should first determine the recommended insulation R-value for your area and climate.

Attic Access Location

If you are constructing a new home or remodeling an existing home, carefully consider the location of an attic access. The location will affect how or whether the attic access should be insulated. If possible, locate the access in an unconditioned part of the house, such as a garage, covered patio, or porch. A garage location, where the vented attic is uninsulated, can eliminate the need for air sealing and insulation.

Attic Hatch

An attic hatch or scuttle hole is simply a removable portion of the ceiling that allows entry to the attic. A scuttle hole is often located in a closet or main hallway.

For air sealing, weatherstripping can be installed either on the hatch itself or on the inside of the trim or base where the hatch rests. Adding a latch bolt will help ensure a tighter seal.

After the trim or base is aligned to seal properly, insulation should be added to the attic side of the hatch. Rigid insulated sheathing is recommended. Cut the insulated sheathing 1/4 inch smaller than the hatch size to allow for clearance when moving the access panel. Apply 3 or 4 inches of insulation to the hatch with construction adhesive and screws.

As an added measure, glue the kraft-paper side of batt insulation to the top of the last layer of rigid insulation. Try to achieve the recommended R-value.

Diagram showing a side view of a scuttle hole that allows access to the attic. On either side of the hole in the attic are barriers called insulation dams, blocking loose-fill insulation from reaching the opening. At the point where the removable door touches the ceiling is a small dot labeled the air seal gasket. The scuttle hole is surrounded by trim. On the attic side, the door is covered with insulation, and the diagram shows how the door can be pushed straight up to gain access to the attic space. The captions read: Scuttle hole cover. Insulation dams prevent loose-fill insulation from falling through access. Hatch lid pushes up and out of the way for access.Download high-resolution diagram:
JPG (ZIP 109 KB) | EPS (ZIP 545 KB)

Attic Pull-Down Stairs

When attic access is gained through pull-down stairs, the frame for the stairs fits in a rough opening and leaves a gap, much like a door or window, which must be sealed. If the gap is small (less than 1/2 inch), caulk can be used as the sealant. If a larger opening exists, then a non-expanding foam or a backing material (backer rod) is recommended in conjunction with the caulk. Expanding foam can be used, but care must be taken because of its highly expansive nature. It could potentially warp the frame and interfere with the ability of the stairs to open and close properly.

To ensure a tight fit between the stairs’ flat panel and the frame, weatherstripping or gasket material should be added either to the frame or panel. Latch bolts may be installed to help ensure a tighter seal.

To insulate attic stairs access, you can construct a lightweight, moveable box from rigid foam or fibrous ductboard to fit over the stairs from the attic side. Insulating kits are also available from weatherization suppliers or local hardware stores.

Diagram showing an attic opening accessed through pull-down stairs. Above the stairs in the attic, an attic stair cover box made from rigid insulation is placed over the opening to seal and insulate the stairs. Weatherstripping is shown along the edge of the stair panel that joins with the edge of the frame and reads: Seal gap between frame and rough opening with caulk, backer, rod, or foam. On the attic side, the cover box has a layer of insulation, and the opening is shielded from loose-fill insulation by insulation dams on either side. The caption here reads: Insulation dams prevent loose-fill insulation from falling through access. Cover box pushes up and out of the way for access.Download high-resolution diagram:
JPG (ZIP 142 KB) | EPS (ZIP 605 KB)

Attic Knee-Wall Door

A knee-wall is typically a partial height wall that is usually found in the upstairs level of finished-attic homes. These walls are notoriously leaky and often uninsulated. Knee-wall doors need to be weatherstripped. They also need a latch that pulls tightly against the weatherstripping and the frame to achieve a solid seal.

Use construction adhesive and screws to attach rigid foam insulation to the attic side of the door. Pay special attention to the clearance between the insulation and the door frame and air sealing details. Adjust insulation levels or R-values to meet those recommended for your area and climate. Also, insulate and air seal the knee walls themselves for maximum energy efficiency.

www.energysavers.com

Leave a Reply Text

Your email address will not be published. Required fields are marked *

newsletter
Want to keep up to date with all our latest news and information?
Subscribe to receive FREE TIPS, all new Radio/Podcast Episodes and Videos that will help you start Dropping your Energy Bill!
Enter your email below to join a world of new knowledge and savings!


LOGO